7435A REV H Norge Dryer Parts List

Search the entire 7435A REV H by part description. Keep descriptions simple, e.g. "belt" or "pump". Need help?

Front drum bearing (drum bearing)

The drum support bearing helps your dryer operate as quietly as possible by allowing the front of the drum to glide smoothly on the felt seal of the front panel when the drum is rotating. If your dryer is noisy or making a squeaking sound, the slides are probably worn and both slides will need to be replaced. This part measures 10” in height and 19 ½” inside width. Four drum glides are used with the drum support bearing and are sold separately. The support bearing is a genuine OEM part. Please remember to disconnect the power to the dryer before starting your repair.

Easy Part #:: EAP960316

Availability:: Special Order

Price:: $34.33

Dryer cycling thermostat (thermostat, internal-bias)

The cycling thermostat with an internal bias heater will continually cycle the heating element off and on to maintain a constant inner temperature in the dryer. This cycling thermostat has a limit of 155 degrees Fahrenheit and a differential of 25 degrees. Meaning that the heating element will cut out at 155 degrees and cycle back on once the internal temperature drops by 25 degrees. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

Easy Part #:: EAP11741405

Availability:: In Stock

Price:: $32.13

Door handle

This white handle can be used with both the freezer door and the fresh food door of many refrigerators. Note: As per manufacture this handle includes the mounting block and screw for the top of the handle, If you need the screw for the bottom it must be ordered separately.

Easy Part #:: EAP427922

Availability:: In Stock

Price:: $54.62

Long oven sensor (sub 12001656)

The oven sensor detects the temperature within the oven cavity and sends the information to the control board. If your oven is not heating evenly, has little or no heat when baking, or is too hot, you may need to replace the sensor. This long oven sensor kit comes with two harness adapters and is a genuine OEM part. Please remember to disconnect the power before starting your repair.

Easy Part #:: EAP1570174

Availability:: In Stock

Price:: $42.94

Sealed burner cap with electrode (sub 12500099)

This burner cap assembly is sold with the spark electrode. Please note this part has been redesigned and no longer requires a gasket. Sold individually.

Easy Part #:: EAP11741733

Availability:: In Stock

Price:: $82.16

Door gasket (gasket, door)

The oven door gasket prevents heat from escaping the oven cavity when in use by creating a seal around the oven door. If your oven has little or no heat when baking, you may need to replace the gasket. This door gasket contains all the attaching clips needed for installation and is a genuine OEM part. Please make sure the oven is cool before installing the door gasket.

Easy Part #:: EAP11749287

Availability:: In Stock

Price:: $100.19

Corner tub baffle - lower right (baffle tub corner rh)

This baffle fits the lower right-hand corner of the dishwasher, is black in color, made of plastic, and has a matching left-hand lower corner baffle that is sold separately. The baffle is used to prevent water from leaking from the tub through the door. If your baffle is damaged, worn, or missing, it will cause the dishwasher to leak and the baffles will need to be replaced. It is recommended that you replace both left and right baffles at the same time. This is a genuine OEM part.

Easy Part #:: EAP263963

Availability:: Special Order

Price:: $14.17

Drive motor with pulley (motor, assembly 60 hz.)

This drive motor operates the dryer by turning the drive belt which spins the drum and will fit most Whirlpool incorporated dryer brands before 1996. If the motor has shorted out, it will no longer turn the drum and will need to be replaced. The drive motor includes the pulley that is not available separately. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Easy Part #:: EAP334304

Availability:: In Stock

Price:: $143.16

Suspension spring

This suspension spring is used with many washing machines. It is made entirely of metal and is seven inches long.

Easy Part #:: EAP11738823

Availability:: In Stock

Price:: $9.30

Tub dampening strap (strap damping)

This part is used to support the tub and keep it in the center of the cabinet to reduce vibration. If your washer is making loud noises, or shakes or moves, one or more of the straps may have broken. It is recommended to replace all 4 tub dampening straps at the same time. This part is sold individually.

Easy Part #:: EAP271100

Availability:: Special Order

Price:: $15.04

Corner tub baffle - lower left (baffle tub corner lh)

This baffle fits the lower left-hand corner of the dishwasher, is black in color, made of plastic and has a matching right-hand lower corner baffle that is sold separately. The baffle is used to prevent water from leaking from the tub through the door. If your baffle is damaged, worn, or missing, it will cause the dishwasher to leak and the baffles will need to be replaced. It is recommended that you replace and install both the left and right baffle at the same time. This is a genuine OEM part.

Easy Part #:: EAP263964

Availability:: Special Order

Price:: $14.17

Drive belt - 51 inches long

This V-style drive belt is about 51-inch long and 3/8-inch wide. This part is made to slip onto the motor pulley to bring the basket up to the speed required. The belt encounters wear and tear over time. If your washer will not drain, spin, or agitate, you may need to replace your belt. It is recommended to disconnect the power to your washer before you start your repair. This V-style belt is a genuine OEM part.

Easy Part #:: EAP11738882

Availability:: In Stock

Price:: $12.61

Refrigerator ice and water filter (filter canister, water)

Easy Part #:: EAP8746144

Availability:: Special Order

Price:: $83.93

Washer drain pump (pump)

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. NOTE: This is a redesigned part. The pump now mounts on to the base of the washer - no mounting plate needed.